[an error occurred while processing this directive]


Disabling protocols: front panel

NOTE
If you are attempting to perform any front panel procedure and you don't see the expected menu choices on the front panel display, the front panel may be locked. For information on how to unlock it, see If the front panel is locked.

Disabling protocols: Phaser 840 printer

  1. When the front panel displays READY TO PRINT, press the down-arrow button until Menu is highlighted. Press Select.
  2. Press the down-arrow button until Printer Configuration is highlighted. Press Select.
  3. Press the down-arrow button until Network Settings is highlighted. Press Select.
  4. To disable EtherTalk (or TokenTalk):
    1. Press the down-arrow button until EtherTalk (or TokenTalk ) is highlighted.
    2. Press Select until Off is displayed.
      • To return the printer to normal operation, press the down-arrow button until Exit is highlighted. Press Select.
      • To disable other protocols, continue with Step 5.
  5. To disable NetWare:
    1. Press the down-arrow button until NetWare is highlighted. Press Select.
    2. Press the down-arrow button until NetWare is highlighted.
    3. Press Select until Off is displayed.
      • To return the printer to normal operation, press the down-arrow button until Exit is highlighted. Press Select.
      • To disable other protocols, press the up-arrow button until Previous Menu is highlighted. Press Select. Continue with Step  6.
  6. To disable TCP/IP:
    1. Press the down-arrow button until TCP/IP is highlighted. Press Select.
    2. Press the down-arrow button until TCP/IP Interface is highlighted.
    3. Press Select until Off is displayed.
      • To return the printer to normal operation, press the down-arrow button until Exit is highlighted. Press Select.
      • To disable other protocols, press the up-arrow button until Previous Menu is highlighted. Press Select. Continue with Step  7.
  7. To disable HTTP:
    1. Press the down-arrow button until HTTP is highlighted.
    2. Press Select until Off is displayed.
    3. To return the printer to normal operation, press the down-arrow button until Exit is highlighted. Press Select.

Disabling protocols: Phaser 740 printer

  1. Press Menu; the front panel displays Help Pages.
    2. NOTE
    When you are in the menu, if the front panel is not used for 5 minutes, the printer returns to the Ready state.
  2. Enter the Network Settings menu by pressing ----> or <---- until the front panel displays Network Settings.
  3. Press Menu; the front panel displays TCP/IP.
  4. Disabling TCP/IP:
    1. Press Menu; the front panel displays Interface.
    2. Press Menu again to display the current status of the protocol: Interface:Enabled or Interface:Disabled. The current status is marked with an asterisk (*) in the upper-right corner of the display.
    3. Press ----> until the front panel displays Interface:Disabled.
    4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays Interface.
    5. Press Exit (the far left button) to return to the TCP/IP display.
  5. Disabling EtherTalk: To return the printer to normal operation, go immediately to Step 8; to continue and disable the EtherTalk protocol, follow these steps:
    1. Press ---->; the front panel displays EtherTalk.
    2. Press Menu; the front panel displays the current status of the protocol: EtherTalk:Enabled or EtherTalk:Disabled. The current status is marked with an asterisk (*) in the upper-right corner of the display.
    3. Press ----> until the front panel displays EtherTalk:Disabled.
    4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays EtherTalk.
  6. Disabling NetWare: To return the printer to normal operation, go immediately to Step 8; to continue and disable the NetWare protocol, follow these steps:
    1. Press ---->; the front panel displays NetWare.
    2. Press Menu again; the front panel displays Interface.
    3. Press Menu to display the current status of the protocol: Interface:Enabled or Interface:Disabled. The current status is marked with an asterisk (*) in the upper-right corner of the display.
    4. Press ----> until the front panel displays Interface:Disabled.
    5. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays Interface.
    6. Press Exit (the far left button) to return to the NetWare display.
  7. Disabling HTTP: To return the printer to normal operation, go immediately to Step 8; to continue and disable the HTTP protocol, follow these steps:
    1. Press ---->; the front panel displays HTTP.
    2. Press Menu; the front panel displays the current status of the protocol: HTTP:Enabled or HTTP:Disabled. The current status is marked with an asterisk (*) in the upper-right corner of the display.
    3. Press ----> until the front panel displays HTTP:Disabled.
    4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays HTTP.
  8. Return the printer to normal operation:
    1. Pres s Exit (the far left button) until the front panel displays Network Settings.
    2. Press Exit (the far left button) again.
      • If you have changed any parameters that require a printer reset to take effect, you will be prompted to reset the printer. If you press Reset, the printer resets. If you press Resume, the front panel displays Network Settings. Press Exit (the far left button); the printer returns to normal operation, but the changes you have made will not take effect until the next time the printer is reset.
      • If you have not changed any parameters that require a printer reset to take effect, the front panel displays Ready.

Disabling protocols: Phaser 780 printer

  1. Press Select; the front panel displays Help Pages.
  2. Press the left arrow or right arrow buttons until the front panel displays Network Settings.
  3. Press Menu to enter the Network Settings menu.
  4. Disabling TCP/IP:
    1. Press the right arrow button until the front panel displays TCP/IP.
    2. Press Menu; the front panel displays Interface.
    3. Press Menu again to display the current status of the protocol: On or Off. The current status is marked with an asterisk (*) in the upper-right corner of the display.
    4. Press the right arrow button until the front panel displays Off.
    5. Press Select to disable the protocol; the front panel briefly displays Selected, then it displays Off again.
    6. Press the right arrow button twice to return to the Network Settings menu.
  5. Disabling EtherTalk (or TokenTalk): To return the printer to normal operation, go immediately to Step 8; to continue and disable the EtherTalk protocol, follow these steps:
    1. Press the right arrow button until the front panel displays EtherTalk or ( TokenTalk ).
    2. Press Menu to display the current status of the protocol: On or Off. The current status is marked with an asterisk (*) in the upper-right corner of the display.
    3. Press the right arrow button until the front panel displays Off.
    4. Press Select to disable the protocol; the front panel briefly displays Selected, then it displays Off again.
    5. Press Exit (the far right button) once to return to the Network Settings menu.
  6. Disabling NetWare: To return the printer to normal operation, go immediately to Step 8; to continue and disable the NetWare protocol, follow these steps:
    1. Press the right arrow button until the front panel displays NetWare.
    2. Press Menu; the front panel displays Interface.
    3. Press Menu again to display the current status of the protocol: On or Off. The current status is marked with an asterisk (*) in the upper-right corner of the display.
    4. Press the right arrow button until the front panel displays Off.
    5. Press Select to disable the protocol; the front panel briefly displays Selected, then it displays Off again.
    6. Press Exit (the far right button) twice to return to the Network Settings menu.
  7. Disabling HTTP: To return the printer to normal operation, go immediately to Step 8; to continue and disable the HTTP protocol, follow these steps:
    1. Press the right arrow button until the front panel displays HTTP.
    2. Press Menu to display the current status of the protocol: On or Off. The current status is marked with an asterisk (*) in the upper-right corner of the display.
    3. Press the right arrow button until the front panel displays Off.
    4. Press Select to disable the protocol; the front panel briefly displays Selected, then it displays Off again.
    5. Press Exit (the far right button) twice to return to the Network Settings menu.
  8. Return the printer to normal operation, press Exit (the far right button) again:
    • If you have changed any parameters that require a printer reset to take effect, you will be prompted to reset the printer. If you press Reset, the printer resets. If you press Resume, the front panel displays Network Settings. Press Exit (the far right button); the printer returns to normal operation, but the changes you have made will not take effect until the next time the printer is reset.
    • If you have not changed any parameters that require a printer reset to take effect, the front panel displays Ready.

Disabling protocols: Phaser 360 printer

  1. Press Menu; the front panel displays Help Pages.
  2. Enter the Network Settings menu by pressing ----> or <---- until the front panel displays Network Settings.
  3. Press Menu; the front panel displays TCP/IP.
  4. Disabling TCP/IP:
    1. Press Menu; the front panel displays Enable Interface.
    2. Press Menu again to display the current status of the protocol: Interface:On or Interface:Off. The current status is marked with an asterisk ( * ) in the upper-right corner of the display.
    3. Press ----> until the front panel displays Interface:Off.
    4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays Enable Interface.
    5. Press Exit to return to the TCP/IP display.
  5. Disabling EtherTalk (or TokenTalk): To return the printer to normal operation, go immediately to Step 8; to continue and disable EtherTalk (or TokenTalk), follow these steps:
    1. Press ---->; the front panel displays EtherTalk or ( TokenTalk ).
    2. Press Menu; the front panel displays the current status of the protocol: Enabled or Disabled. The current status is marked with an asterisk ( * ) in the upper-right corner of the display.
    3. Press ----> until the front panel displays Disabled.
    4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays EtherTalk or ( TokenTalk ).
  6. Disabling NetWare: To return the printer to normal operation, go immediately to Step 8; to continue and disable the NetWare protocol, follow these steps:
    1. Press ---->; the front panel displays NetWare.
    2. Press Menu again; the front panel displays Enable Interface.
    3. Press Menu to display the current status of the protocol: Interface:On or Interface:Off. The current status is marked with an asterisk ( * ) in the upper-right corner of the display.
    4. Press ----> until the front panel displays Interface:Off.
    5. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays Enable Interface.
    6. Press Exit to return to the NetWare display.
  7. Disabling HTTP: To return the printer to normal operation, go immediately to Step 8; to continue and disable the HTTP protocol, follow these steps:
    1. Press ---->; the front panel displays HTTP.
    2. Press Menu again; the front panel displays the current status of the protocol: HTTP:Enabled or HTTP:Disabled. The current status is marked with an asterisk ( * ) in the upper-right corner of the display.
    3. Press ----> until the front panel displays HTTP:Disabled.
    4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays HTTP.
  8. Return the printer to normal operation:
    1. Press Exit until the front panel displays Network Settings.
    2. Press Exit again.
      • If you have changed any parameters that require a printer reset to take effect, you will be prompted to reset the printer. If you press Reset, the printer resets. If you press Resume, the front panel displays Network Settings. Press Exit; the printer returns to normal operation, but the changes you have made will not take effect until the next time the printer is reset.
      • If you have not changed any parameters that require a printer reset to take effect, the front panel displays Ready.

Return to Topic List
[an error occurred while processing this directive]