1. Press Menu; the front panel displays Help Pages.

NOTE When you are in the menu, if the front panel is not used for 5 minutes, the printer returns to the Ready state.

2. Enter the Network Settings menu by pressing ----> or <---- until the front panel displays Network Settings.
3. Press Menu; the front panel displays TCP/IP.
4. Disabling TCP/IP:
1. Press Menu; the front panel displays Interface.
2. Press Menu again to display the current status of the protocol: Interface:Enabled or Interface:Disabled. The current status is marked with an asterisk (*) in the upper-right corner of the display.
3. Press ----> until the front panel displays Interface:Disabled.
4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays Interface.
5. Press Exit (the far left button) to return to the TCP/IP display.
5. Disabling EtherTalk: To return the printer to normal operation, go immediately to Step 8; to continue and disable the EtherTalk protocol, follow these steps:
1. Press ---->; the front panel displays EtherTalk.
2. Press Menu; the front panel displays the current status of the protocol: EtherTalk:Enabled or EtherTalk:Disabled. The current status is marked with an asterisk (*) in the upper-right corner of the display.
3. Press ----> until the front panel displays EtherTalk:Disabled.
4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays EtherTalk.
6. Disabling NetWare: To return the printer to normal operation, go immediately to Step 8; to continue and disable the NetWare protocol, follow these steps:
1. Press ---->; the front panel displays NetWare.
2. Press Menu again; the front panel displays Interface.
3. Press Menu to display the current status of the protocol: Interface:Enabled or Interface:Disabled. The current status is marked with an asterisk (*) in the upper-right corner of the display.
4. Press ----> until the front panel displays Interface:Disabled.
5. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays Interface.
6. Press Exit (the far left button) to return to the NetWare display.
7. Disabling HTTP: To return the printer to normal operation, go immediately to Step 8; to continue and disable the HTTP protocol, follow these steps:
1. Press ---->; the front panel displays HTTP.
2. Press Menu; the front panel displays the current status of the protocol: HTTP:Enabled or HTTP:Disabled. The current status is marked with an asterisk (*) in the upper-right corner of the display.
3. Press ----> until the front panel displays HTTP:Disabled.
4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays HTTP.
8. Return the printer to normal operation:
1. Press Exit (the far left button) until the front panel displays Network Settings.
2. Press Exit again.
• If you have changed any parameters that require a printer reset to take effect, you will be prompted to reset the printer. If you press Reset, the printer resets. If you press Resume, the front panel displays Network Settings. Press Exit (the far left button); the printer returns to normal operation, but the changes you have made will not take effect until the next time the printer is reset.
• If you have not changed any parameters that require a printer reset to take effect, the front panel displays Ready.

1. Press Select; the front panel displays Help Pages.
2. Press the left arrow or right arrow buttons until the front panel displays Network Settings.
3. Press Menu to enter the Network Settings menu.
4. Disabling TCP/IP:
1. Press the right arrow button until the front panel displays TCP/IP.
2. Press Menu; the front panel displays Interface.
3. Press Menu again to display the current status of the protocol: On or Off. The current status is marked with an asterisk (*) in the upper-right corner of the display.
4. Press the right arrow button until the front panel displays Off.
5. Press Select to disable the protocol; the front panel briefly displays Selected, then it displays Off again.
6. Press Exit (the far right button) twice to return to the Network Settings menu.
5. Disabling EtherTalk (or TokenTalk): To return the printer to normal operation, go immediately to Step 8; to continue and disable the EtherTalk protocol, follow these steps:
1. Press the right arrow button until the front panel displays EtherTalk or ( TokenTalk ).
2. Press Menu to display the current status of the protocol: On or Off. The current status is marked with an asterisk (*) in the upper-right corner of the display.
3. Press the right arrow button until the front panel displays Off.
4. Press Select to disable the protocol; the front panel briefly displays Selected, then it displays Off again.
5. Press Exit (the far right button) once to return to the Network Settings menu.
6. Disabling NetWare: To return the printer to normal operation, go immediately to Step 8; to continue and disable the NetWare protocol, follow these steps:
1. Press the right arrow button until the front panel displays NetWare.
2. Press Menu; the front panel displays Interface.
3. Press Menu again to display the current status of the protocol: On or Off. The current status is marked with an asterisk (*) in the upper-right corner of the display.
4. Press the right arrow button until the front panel displays Off.
5. Press Select to disable the protocol; the front panel briefly displays Selected, then it displays Off again.
6. Press Exit (the far right button) twice to return to the Network Settings menu.
7. Disabling HTTP: To return the printer to normal operation, go immediately to Step 8; to continue and disable the HTTP protocol, follow these steps:
1. Press the right arrow button until the front panel displays HTTP.
2. Press Menu to display the current status of the protocol: On or Off. The current status is marked with an asterisk (*) in the upper-right corner of the display.
3. Press the right arrow button until the front panel displays Off.
4. Press Select to disable the protocol; the front panel briefly displays Selected, then it displays Off again.
5. Press Exit (the far right button) twice to return to the Network Settings menu.
8. Return the printer to normal operation, press Exit (the far right button) again:
• If you have changed any parameters that require a printer reset to take effect, you will be prompted to reset the printer. If you press Reset, the printer resets. If you press Resume, the front panel displays Network Settings. Press Exit (the far right button); the printer returns to normal operation, but the changes you have made will not take effect until the next time the printer is reset.
• If you have not changed any parameters that require a printer reset to take effect, the front panel displays Ready.

1. Press Menu; the front panel displays Help Pages.
2. Enter the Network Settings menu by pressing ----> or <---- until the front panel displays Network Settings.
3. Press Menu; the front panel displays TCP/IP.
4. Disabling TCP/IP:
1. Press Menu; the front panel displays Enable Interface.
2. Press Menu again to display the current status of the protocol: Interface:On or Interface:Off. The current status is marked with an asterisk ( * ) in the upper-right corner of the display.
3. Press ----> until the front panel displays Interface:Off.
4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays Enable Interface.
5. Press Exit to return to the TCP/IP display.
5. Disabling EtherTalk (or TokenTalk): To return the printer to normal operation, go immediately to Step 8; to continue and disable EtherTalk (or TokenTalk), follow these steps:
1. Press ---->; the front panel displays EtherTalk or ( TokenTalk ).
2. Press Menu; the front panel displays the current status of the protocol: Enabled or Disabled. The current status is marked with an asterisk ( * ) in the upper-right corner of the display.
3. Press ----> until the front panel displays Disabled.
4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays EtherTalk or ( TokenTalk ).
6. Disabling NetWare: To return the printer to normal operation, go immediately to Step 8; to continue and disable the NetWare protocol, follow these steps:
1. Press ---->; the front panel displays NetWare.
2. Press Menu again; the front panel displays Enable Interface.
3. Press Menu to display the current status of the protocol: Interface:On or Interface:Off. The current status is marked with an asterisk ( * ) in the upper-right corner of the display.
4. Press ----> until the front panel displays Interface:Off.
5. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays Enable Interface.
6. Press Exit to return to the NetWare display.
7. Disabling HTTP: To return the printer to normal operation, go immediately to Step 8; to continue and disable the HTTP protocol, follow these steps:
1. Press ---->; the front panel displays HTTP.
2. Press Menu again; the front panel displays the current status of the protocol: HTTP:Enabled or HTTP:Disabled. The current status is marked with an asterisk ( * ) in the upper-right corner of the display.
3. Press ----> until the front panel displays HTTP:Disabled.
4. Press OK to disable the protocol; the front panel briefly displays Selected, then it displays HTTP.
8. Return the printer to normal operation:
1. Press Exit until the front panel displays Network Settings.
2. Press Exit again.
• If you have changed any parameters that require a printer reset to take effect, you will be prompted to reset the printer. If you press Reset, the printer resets. If you press Resume, the front panel displays Network Settings. Press Exit; the printer returns to normal operation, but the changes you have made will not take effect until the next time the printer is reset.
• If you have not changed any parameters that require a printer reset to take effect, the front panel displays Ready.

If you are attempting to perform any front panel procedures and you don't see the expected menu choices on the front panel display, the front panel may be locked. This topic describes how to unlock the front panel.

The printer allows a system administrator to lock the front panel menu by downloading a utility file. In this protected mode, you can print the pages in the Help Pages menu, but cannot modify any settings in the rest of the menus. For more information on locking the front panel menu with a utility file, refer to your printer's user documentation.

• Press Menu. The front panel displays the following message:

Help Pages <---- ----> Menu

When the front panel is locked and you press Menu, the display shows only the pages in the Help Pages menu (without the heading):

To access the entire menu with the front panel locked, you must use a special key sequence to enter the menu.

• Press and hold down Menu and press Exit. The front panel displays the following message:

Help Pages <---- ----> Menu

• You now have access to all front panel menus.