PhaserShare

Configure Printer Defaults (Phaser 360 printer) This page allows you to view or set general printer settings. Making these settings from this page is equivalent to making the corresponding settings from the printer's front panel, which means the settings are retained in the printer's memory and are overridden on a job-by-job basis by settings made from the printer driver. The actual settings displayed depend on the printer. This page also provides fields for setting the printer's clock. Settable parameters on the Configure Printer Defaults page for the Phaser 360 printer Setting Description Print Quality Mode See your printer's user documentation for details. TekColor Correction See your printer's user documentation for details. Media Source See your printer's user documentation for details. Startup Page Enabled Yes: A Startup Page prints every time the printer is reset. No: The Startup Page is not printed. SCSI Start Job Run: Enables automatic execution of a file named SysStart (if one is found) on a hard disk connected to the printer's SCSI port, each time the printer is turned on or reset. Skip: Disables automatic execution of the SysStart file. Status Refresh Delay The value in this field controls how often the information available from the Start status update link (on the Current Status Page) is updated. The factory default is 60 seconds. You can choose from a menu of values from 15 to 600 seconds. Check Print Enabled The Check Print option in the supported printer drivers causes the printer to pause after printing the first page of a multiple-page print job. This allows you to check the colors or print quality before continuing with the rest of the job. After checking, you can resume or cancel printing from the printer's front panel. Printing resumes automatically after the time period specified in the Check Print Timeout field. When Yes is selected in this list box, the printer's Check Print feature is enabled, and you can turn it on from the driver. If No is selected, Check Print is disabled, and turning it on from the driver has no effect. Check Print Timeout This field contains the Check Print timeout value in seconds. This is the amount of time the printer pauses before printing the rest of the job. You may enter a value between 0 and 10080 minutes. A value of 0 causes the printer to pause indefinitely until it receives a command from the front panel. This timeout is used when the Check Print list box is set to Yes and the Check Print option has been selected in the printer driver. Job Timeout The value in this field determines how long the printer waits during an interrupted print job before ending the job. Enter a value in seconds. A value of 0 indicates no timeout; that is, the printer does not time out on an interrupted job. The value entered must be between 0 and 65535. Wait Timeout The value in this field determines how long the printer waits for expected data during a print job. If the printer does not receive expected data within the specified period of time after the job is started, the printer cancels the job. Enter a value in seconds. A value of 0 indicates no timeout; that is, the printer does not time out while waiting for data. The value entered must be between 0 and 65535. Manual Feed Timeout The value in this field determines how long the printer waits for paper to be inserted into the manual feed slot for a manual feed print job. If paper is not inserted within the specified period of time after the job is sent to the printer, the printer attempts to pick paper from one of the paper trays. Enter a value in seconds. A value of 0 indicates no timeout; that is, the printer does not time out while waiting for paper to be inserted. The value entered must be between 0 and 65535. Energy Star Timeout The value in this field determines how long the printer must remain in an idle state before entering Energy Star mode. (In Energy Star mode, the printer uses much less power than it does in an idle state, but it returns to normal operation upon receiving print jobs.) Enter a value in hours; the value entered must be between 1 and 999. Current Date and Time This field reports the current setting for the printer's clock. Click on the link to display the View and Configure Time of Day Settings page, where you can set the clock. View and Configure Time of Day Settings (Phaser 360 only) This page provides fields for setting the printer's clock. Enter the current time for your time zone, but be sure to enter the offset from Greenwich Mean Time. The following table shows the correct offsets for U.S. time zones. Time zone Offset from Greenwich Mean Time Eastern Daylight -4 Eastern Standard -5 Central Daylight -5 Central Standard -6 Mountain Daylight -6 Mountain Standard -7 Pacific Daylight -7 Pacific Standard -8 Return to PhaserLink Help Home Page						Support Home Page Network Printers Support Home Additional Information Register your Printer ASPs & TPMs About Software Support Color Connection Printer Warranties Material Safety Data Sheets Supplies & Cartridge Recycling Program